Design Of A Turbine Runner
ABSTRACT
Use of renewable energy has been of great interest since last few years, especially the hydropower energy. Usually electricity is generated from hydropower energy, which is obtained from potential pressure heads, water discharge and hydro sites. Based on the location constraints, different types of hydro turbines can be designed and developed to generate electricity. The primary concern is to reduce the dependency on fossil fuels and increase the use of renewable power in rural areas. In this paper, designing of Kaplan turbine runner mechanism was discussed.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
- BACKGROUND OF THE PROJECT
- AIM OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- APPLICATIONS OF TURBINE RUNNER
- DISADVANTAGE OF KAPLAN TURBINE
CHAPTER TWO
LITERATURE REVIEW
- REVIEW OF THE STUDY
- HISTORICAL BACKGROUND OF HYDROPOWER GENERATION
- REVIEW OF PREVIOUS WORK ON KAPLAN TURBINE DESIGN AND OPTIMIZATION
- PROPOSED WORK
- CLASSIFICATION OF TURBINES
- TURBINES IN HYDROPOWER
- MAIN COMPONENTS OF KAPLAN TURBINE
- WORKING PRINCIPLE OF KAPLAN TURBINE
CHAPTER THREE
METHODOLOGY
- THEORETICALDESIGN
- TURBINE BLADEDESIGN
- COORDINATETRANSLATION
- DESIGNING OF THE GUIDE VANES
- CFD ANALYSIS
- CFD SOLVING SETUP
- LIMITATIONS
CHAPTER FOUR
- RESULT AND DISCUSSION
- OPTIMIZATION OF THE RUNNER WHEEL WITH CFD
- COMPARISON OF THEORETICAL AND CFD OPTIMIZED DESIGNS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
Hydropower, generated mainly from hydroelectric dams, is a clear, green, and sustainable source of energy that produces cheaper electricity and lowers carbon emissions. Because of its high energy density, hydropower is the most efficient and most primarily available renewable power source to produce electricity [7]. In order to obtain greater efficiency, hydraulic turbines installed in the hydroelectric power plants have to be suitable, depending on the discharge of the site and head. There are a lot of hydraulic turbines available which are generally classified into two categories:
1] Impulse turbines
2] Reaction turbines
A hydraulic turbine in which all hydraulic energy of water gets converted into kinetic energy before the water reaches to the runner of the turbine is called impulse turbine. While in case of reaction turbine, some amount of available hydraulic energy is converted into kinetic energy before it strikes on the runner of the turbine. For flow head range available at the chosen site, reaction turbine is well suited. Reaction turbines include Propeller, Kaplan, and Francis turbine [2].
1.2 AIM OF THE PROJECT
There are different types of turbine runners or turbine blade, and all of them are made to achieve the same purpose of generating electricity in hydro-power plants. The main aim of this work is to design Kaplan type of turbine runner.
1.3 SIGNIFICANCE OF THE PROJECT
Turbine blade is the most widely used turbine in hydro-power plants to generate electricity. Mixed flow turbine is also used in irrigation water pumping sets to pump water from ground for irrigation. It is efficient over a wide range of water head and flow rate. It is most efficient hydro-turbine we have till date.
1.4 APPLICATIONS OF TURBINE RUNNER
- Kaplan turbines are widely used throughout the world for electrical power production.
- It can work more efficiently at low water head and high flow rates as compared with other types of turbines.
- It is smaller in size and easy to construct.
- The efficiency of Kaplan turbine is very high as compares with other hydraulic turbine.
1.5 DISADVANTAGE OF KAPLAN TURBINE
The only disadvantage of kaplan turbine is cavitation, which occurs due to pressure drop in draft tube. Use of draft tube and proper material generally stainless steel for the runner blades may reduce the cavitation problem to a greater extent.
The Title Page should be the first section of your project “Design Of A Turbine Runner”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design Of A Turbine Runner by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design Of A Turbine Runner should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design Of A Turbine Runner research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design Of A Turbine Runner project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work