Design And Planning Of Base Transceiver Station
ABSTRACT
This project work is titled design and planning of a base transceiver station. A BTS is also known as a base station (BS), radio base station (RBS) or node B (eNB).
A base transceiver station (BTS) or cell site is a piece of equipment that facilitates wireless communication between user equipment (UE) and a network. UEs are devices like mobile phones (handsets), WLL phones, computers with wireless internet connectivity, WiFi and WiMAX gadgets etc. The network can be that of any of the wireless communication technologies like GSM, CDMA, WLL, WAN, WiFi, WiMAX.
The aim of this work is to design and plan a base station that can facilitates wireless communication between user equipment (UE) and a network.
TABLE OF CONTENTS
Title Page
Approval Page
Dedication
Acknowledgement
Abstract
Table of Content
CHAPTER ONE
1.0 Introduction
1.1 Objective of the study
1.2 Significance of the study
CHAPTER TWO
2.0 Literature review
2.1 Review of base transceiver station
2.2 Review of open GSM infrastructure
2.3 Historical background of base transceiver station
2.4 Review of GSM network architecture
2.5 Review of base station controller
CHAPTER THREE
3.0 Methodology
3.1 Block diagram of a base transceiver
3.2 Base transceiver general architecture
3.3 Base transceiver station structure
3.4 Configuration & installation of a base transceiver station (bts)
3.5 Components of the base transceiver station
3.6 General function
CHAPTER FOUR
4.1 Tests and Diagnostics
4.2 System standard testing
4.3 system maintenance
4.4 Cooling for the base transceiver station
CHAPTER FIVE
5.1 Conclusion
5.2 References
CHAPTER ONE
1.0 INTRODUCTION
Communication as an important aspect of human life. As man continues daily life. The need to continually communicate, acquire and share information becomes more obvious. It then becomes important and necessary to be more information conscious not only in the content but as well as the speed of its transfer. This work centers on the design of a Base Transceiver Station network which is designed in order to reduce communication problems and improve information dissemination within the community. The results of these studies, and measurements were used to recommend suitable transmitting location and antenna height measurements were used to recommend suitable transmitting parameters such as radiated power. Antenna gain and operating frequencies with a view to recommending an appropriate base station system equipment specification.
A network may be any wireless technology, like Code Division Multiple Access (CDMA), Global System for Mobile Communications (GSM), Worldwide Interoperability for Microwave Access (WiMAX) or Wi-Fi. However, because a BTS is associated with mobile communications technologies, it refers to the equipment that creates the “cell” in a cellular network. Sometimes, an entire base station, plus its tower, is improperly referred to as a base transceiver station (BTS) or cell phone tower.
As part of a cellular network, a base transceiver station (BTS) has equipment for the encryption and decryption of communications, spectrum filtering equipment, antennas and transceivers (TRX) to name a few. A BTS typically has multiple transceivers that allow it to serve many of the cell’s different frequencies and sectors.
A parent base station controller (BSC) controls all BTSs via the base station control function (BCF) – either a separate unit or integrated with the TRX for compact base stations. The BCF provides a connection to the network management system (NMS) and manages the transceiver’s operational states.
The function of the base transceiver station (BTS) remains the same – no matter what type of wireless technology is used.
A base transceiver station (BTS) is a piece of network equipment that facilitates wireless communication between a device and network.
A BTS consists of the following:
- Antennas that relay radio messages
- Transceivers
- Duplexers
- Amplifiers
A BTS is also known as a base station (BS), radio base station (RBS) or node B (eNB).
OBJECTIVE OF THE STUDY
The main objective of this study is to design and plan a wireless network (typically cellular or PCS) that includes the transmitters and receivers, antennas and tower that is used to communicate with mobile radios.
SIGNIFICANCE OF THE COURSE
This study exposes us to the architecture, function descriptions and minimum requirements for integration of a set of common modules into a base transceiver station (BTS). It:
- Defined an internal modular structure of base stations.
- Defined a set of standard BTS modules with specified form, fit and function such that BTS vendors can acquire and integrate modules from multiple vendors in an OEM fashion.
- Defined internal digital interfaces between BTS modules to assure interoperability and compatibility.
- Supported different access technologies such as GSM, Enhanced Data Rates for GSM Evolution (EDGE), CDMA2000, WCDMA .
The Title Page should be the first section of your project “Design And Planning Of Base Transceiver Station”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design And Planning Of Base Transceiver Station by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design And Planning Of Base Transceiver Station should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design And Planning Of Base Transceiver Station research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design And Planning Of Base Transceiver Station project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work