Design And Construction Of An Arduino-Based Wireless Door Bell
ABSTRACT
Today the traditional wired type of doorbells are gradually getting obsolete and are being replaced by the advanced wireless type of doorbells that are easier to install due to their hassle free set-ups. Wireless doorbell system generally comprises at least one RF transmitter powered by a battery or other power source, such as existing electrical wiring, and a RF receiver. In response to the depression of a button or other activating means on the transmitter, an electrical circuit is completed within the transmitter which energizes an oscillator or other means for generating a RF signal. The generated RF signal is then, with the aid of an antenna, transmitted a certain distance for reception by the receiver. The receiver alerts, for example, a homeowner that the doorbell button has been depressed by producing an audible signal, such as a tone or melody, upon detecting the transmitted RF signal. In this project, an Arduino based Wireless Doorbell was built. The project is implemented using RF Module for wireless communication and also an Arduino UNO board to analyze the data.
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
- BACKGROUND OF THE PROJECT
- PROBLEM STATEMENT
- OBJECTIVE OF THE PROJECT
- SCOPE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- LIMITATION/ PROBLEM OF THE PROJECT
- APPLICATIONS OF THE PROJECT
- METHODOLOGY
- PROJECT ORGANISATION
CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 HISTORICAL BACKGROUND OF THE STUDY
2.2 REVIEW OF DIFFERENT TYPES OF DOOR BELL
2.3 USES OF WIRELESS TECHNOLOGIES
2.4 FUTURE OF WIRELESS TECHNOLOGIES
CHAPTER THREE
3.0 DESIGN METHODOLOGY
3.1 SYSTEM BLOCK DIAGRAM
3.2 SYSTEM OPERATION
3.3 SYSTEM WORKING PRINCIPLE
3.4 SYSTEM CIRCUIT DIAGRAM
3.5 ELECTRONIC COMPONENTS
CHAPTER FOUR
4.0 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
4.2 CASING AND PACKAGING
4.3 ASSEMBLING OF SECTIONS
4.4 TESTING OF SYSTEM OPERATION
CHAPTER FIVE
5.1 CONCLUSIONS
5.2 REFERENCES
3.3 RECOMMENDATION
CHAPTER ONE
1.0 INTRODUCTION
A doorbell is a signaling device typically placed near an entry door to a building. When a visitor presses a button the bell rings inside the building, alerting the occupant to the presence of the visitor. Although the first doorbells were mechanical, activated by pulling a cord, modern doorbells are electric — they are actuated by an electric switch [1].
However, this work is wireless doorbell which is the modification of wired doorbell. Wireless doorbell systems that do not require wall wiring have become popular. The doorbell button contains a built-in radio transmitter powered by a battery. When the button is pushed, the transmitter sends a radio signal to the receiver unit, which is plugged into a wall outlet inside the building. When the radio signal is detected by the receiver [3], it activates a sound chip that plays the sound of gongs through a loudspeaker—either a two-note “ding-dong” sound or a longer chime sequence such as Westminster Quarters. To avoid interference by nearby wireless doorbells on the same radio frequency, the units can usually be set by the owner to different radio channels [2].
In larger metropolitan cities, a trend has developed over the past decade that uses telephone technology to wirelessly signal doorbells as well as to answer the doors and remotely release electric strikes. In many cities throughout the world, this is the predominant form of doorbell signalling.
A typical wireless doorbell system generally comprises at least one RF transmitter powered by a battery or other power source, such as existing electrical wiring, and a RF receiver. In response to the depression of a button or other activating means on the transmitter, an electrical circuit is completed within the transmitter which energizes an oscillator or other means for generating a RF signal. The generated RF signal is then, with the aid of an antenna, transmitted a certain distance for reception by the receiver. The receiver alerts, for example, a homeowner that the doorbell button has been depressed by producing an audible signal, such as a tone or melody, upon detecting the transmitted RF signal [2].
In this project, we have designed an Arduino based Wireless Doorbell using simple hardware. The project is implemented using RF Module for wireless communication and also an Arduino UNO board to analyze the data.
1.1 BACKGROUND OF THE PROJECT
Today the traditional wired type of doorbells are gradually getting obsolete and are being replaced by the advanced wireless type of doorbells that are easier to install due to their hassle free set-ups.
Wireless doorbell systems have become an increasingly popular option for persons wishing either to replace their current doorbell system or to add additional doorbells at their place of business or residence. A typical wireless doorbell system generally comprises at least one RF transmitter powered by a battery or other power source, such as existing electrical wiring, and a RF receiver [2]. In response to the depression of a button or other activating means on the transmitter, an electrical circuit is completed within the transmitter which energizes an oscillator or other means for generating a RF signal. The generated RF signal is then, with the aid of an antenna, transmitted a certain distance for reception by the receiver. The receiver alerts, for example, a homeowner that the doorbell button has been depressed by producing an audible signal, such as a tone or melody, upon detecting the transmitted RF signal [3].
1.2 PROBLEM STATEMENT
Conventionally, doorbell is activated once the visitor approaches the door of the host by making contact / pressing the switch at the door, and this gives the visitor stress when locating the switch most especially at night when everywhere is covered with darkness. However, this device came into existence to overcome the problem of searching for the switch before a door alarm is rung. This device rings an alarm once the visitor approaches the door from a set distance using RF signal.
1.3 OBJECTIVE OF THE PROJECT
The main aim of the study is to build an arduino based wireless door bell. The objectives of the study are:
- To build the system prototype
- To alert the occupant to the presence of the visitor.
- To interface arduino with rf circuits
1.4 SCOPE OF THE PROJECT
Wireless doorbell systems which employ radio frequency (“RF”) transmitters and receivers. Both the transmitter and receiver is powered batteries or other power source, such as existing electrical wiring. The wireless transmitter, comprising a power source; a metal case divided into two or more electrically isolated sections by one or more electrically non-conductive gaps there between; a means disposed within said metal case for closing an electric circuit; an antenna enclosed within said metal case; a means for generating a radio frequency signal enclosed within said metal case; and an electric circuit connected to said power source, said means for closing said electric circuit, said antenna and said means for generating a radio frequency signal; wherein said means for generating a radio frequency signal is energized by said power source and a radio frequency signal is produced when said means for closing an electric circuit is moved to a position which closes said electric circuit.
1.5 SIGNIFICANCE OF THE PROJECT
A wireless doorbell does not have wires that hassle the installation. Installation is now simple. Installing the wireless doorbell is as easy as removing the installed wired doorbell and putting on batteries on the wireless doorbell and placing it to its location. Also, the wireless doorbell is portable; it can be moved wherever the homeowners like it to be placed. This would be very helpful for future remodeling or refurnishing of the house. Wireless doorbell is more versatile over Wired Doorbell.
1.6 LIMITATION/ PROBLEM OF THE PROJECT
- Both the Transmitter and Receiver parts of the circuit must be always turned on i.e. there should always be power.
- No additional security like camera integration and hence, the ringer of the bell can’t be determined.
1.7 APPLICATION OF THE PROJECT
Since the mode of communication is RF, the range is considerably large that other wireless technologies.
The project is suitable for homes, shops, garages, hospitals, offices etc.
1.8 METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:
- Study of the previous work on the project so as to improve it efficiency.
- Draw a block diagram.
- Test for continuity of components and devices,
- Design and calculation for the device was carried out.
- Studying of various component used in circuit.
- Construction of the circuit was carried out.
- Finally, the whole device was cased and final test was carried out.
1.9 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to the study. In this chapter, the background, significance, application, objective limitation and problem of the study were discussed.
Chapter two is on literature review of this study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
The Title Page should be the first section of your project “Design And Construction Of An Arduino-Based Wireless Door Bell”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design And Construction Of An Arduino-Based Wireless Door Bell by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design And Construction Of An Arduino-Based Wireless Door Bell should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design And Construction Of An Arduino-Based Wireless Door Bell research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design And Construction Of An Arduino-Based Wireless Door Bell project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work