Design And Construction Of An Arc Welding Machine
The machine is designed to serve with an output of 250A. it has two pats which are the primary and secondary parts. The primary part, through which voltage is supplied to the machine has 180 turns which is made of 2mm2 S.W.G 14 copper coil. The secondary part has 45 turns made of 4mm2 S.W.G 8 copper coil.
Both turns are wound on separate limb of the laminated core. The voltage from primary turns flows to the secondary turn by induction.
The machine contain a power switch through which the machine can be switched on or off when connected to the power source. The indication light simply shows when the machine is on or off which is equally controlled by the power switch.
The fan connected to the machine helps in the looking of the temperature of the machine, it gets started once the machine is on.
The welding current is adjusted by varying the spacing between the primary and secondary windings when the cranks is rotated, clockwise the insulating block between the two winding moves down, the magnetic flux leakage and the inductive impedance are increased, thereby reducing the welding current in the secondary windings. Also as the insulating block is moved upward, away between the two turns, the magnetic flux leakage and the inductive impedance are brought down, causing the welding current to rise.
1.0 INTRODUCTION
The Arc welding machine is the type that uses an electric power as an input, which is being supplied through the primary and then transferred to the secondary winding by induction which can the be used to carry out welding work by connecting to the output terminal the welding cables.
The output of the machine is designed in a way that it can be varied by adjusting the crank of the machines in clockwise or anti-clockwise direction in either to increase or decrease the output current respectively depending on the size of the material it is to be used on.
AIMS/OBJECTIVES
This group agreed in bringing ideals together as one body to construct a functional 250Amp Arc welding machine, which will be fir in both industrial and agricultural field.
The machine takes an input ranging from 220volt to 230volts which will be induced to the secondary windings then giving out it’s output towards the output terminals of the secondary windings.
Due to the variation on the size of the metallic materials, the machine the machine is designed in such a way that it’s output current can be varied in other to suit the material it works one.
1.2 SCOPE OR LIMITATION
The machine is designed to be supplied with an input ranging from 220volts to 240volts. It is a single phase machine which gives it’s output through the output terminal of it’s secondary windings. The machine with it’s maximum output as 250Amps can be re-adjusted to a lower value when such output is considered too high.
He machine is equally designed to work with electrodes with their gauge ranging from 8,10 and 12 depending on the nature of the material and in all cases, it is expected to serve continuously for about 48hours provided the required input voltage is being supplied to it.
1.3 DEFINITION OF TERMS
Listed below are the definition of some of the term used in this project:
1.3.1 Coil: This is a copper conductor used to form the primary and secondary windings from which current enters and leaves out of the transformer.
1.3.2 Insulator: This can be defined as those materials that do not allow the passage of electric current through them. They are used to insulate the windings from each other as well as the laminated core.
1.3.3 Windings: This is the copper wire used as the coil, which is then wound on the limb of the laminated core from which current enters and leaves the circuit.
1.3.4 Flux: This can be defined as the magnetic effect experienced in the circuit due to the flow of current in the windings.
1.3.5 Laminated core: This is the core lamination which is inform of strips joined in such a way that the joints in the alternate layers are staggered in such a way as to avoid the presence of narrow gaps right through the cross-section of the core. It is constructed with transformer sheet steel lamination assembled to provide a continuous magnetic path. It consists of the joke and the limb which are equally laminated to reduce the lost due to eddy current.
1.3.6 Limb: This can be defined as the vertical parts of the lamination core on which the primary and secondary windings are wound separately on the different limbs of the laminated core
1.3.7 Yoke: This is the outer horizontal parts of the lamination core, which help in the reduction of eddy current losses, as well as provide mechanical support to the windings. It also carries the magnetic flux produced by the poles.
Title Page/Approval Page
Certification
Dedication
Acknowledgement
Abstract
Table Of Content
Chapter One
1.0 Introduction
1.1 Aims/Objective
1.2 Scope Or Limitation
1.3 Definition Of Terms
Chapter Two
2.0 Literature Review
2.1 Transformer Design
2.2 Coil Design
2.3 Core Design
2.4 Equivalent Circuit Of The Machine
2.5 Machine Design
2.6 Operation Of Machine
2.7 Leakage Flux Reduction
2.8 Specification From Design
Chapter Three
3.0 Construction
3.1 Lamination
3.2 Transformer Former
3.3 Copper Coil
3.4 Insulating Materials
3.5 Methodology
3.6 Casing
3.7 Coupling
3.8 Electrical Holder
Chapter Four
4.0 Testing And Finding
4.1 Open-Circuit Test
4.2 Short-Circuit Test
4.3 Test Analysis
4.4 Conditions For Operation
4.5 Cost Analysis
Chapter Five
5.0 Conclusion
5.1 Recommendation
References
The Title Page should be the first section of your project “Design And Construction Of An Arc Welding Machine”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design And Construction Of An Arc Welding Machine by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design And Construction Of An Arc Welding Machine should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design And Construction Of An Arc Welding Machine research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design And Construction Of An Arc Welding Machine project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work