Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply
ABSTRACT
Phase sequence is the order in which the rotated voltage or current generated by 3-phase system attain peak or maximum value. Each sequence voltage is 120 degree apart. Therefore, the maximum value achieved by each sequence is at the definite time interval. Based on this individual response time a technique of phase detection system is discussed in this paper. When phase sequences are reverses at that time a relay system operates and a three phase supply gets turns off. A micro-controller is used to incorporate the algorithm into it.
TABLE OF CONTENTS
TITLE PAGE
CERTIFICATION
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENTS
CHAPTER ONE
1.0 INTRODUCTION
1.1 OBJECTIVE OF THE PROJECT
1.2 PURPOSE OF THE PROJECT
1.3 EFFECTS OF WRONG PHASE SEQUENCE
1.4 SIGNIFICANCE OF THE PROJECT
1.5 SCOPE OF THE PROJECT
1.6 ADVANTAGES OF THE PROJECT
1.7 PROJECT ORGANISATION
CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 REVIEW OF ELECTRICAL PHASES
2.2 REVIEW OF THREE-PHASE ELECTRIC POWER
2.3 REVIEW OF THREE-PHASE LOADS
CHAPTER THREE
3.0 DESIGN METHODOLOGY
3.1 SYSTEM BLOCK DIAGRAM
3.2 SYSTEM CIRCUIT DIAGRAM
3.3 SYSTEM OPERATION
3.4 COMPONENT DESCRIPTION
3.5 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE
4.2 CASING AND PACKAGING
4.3 ASSEMBLING OF SECTIONS
4.4 PACKAGING
4.5 MOUNTING PROCEDURE
4.6 TESTING
4.7 PROBLEM ENCOUNTERED
4.8 FUTURE SCOPE
CHAPTER FIVE
5.1 CONCLUSION
5.2 RECOMMENDATION
5.3 REFERENCE
CHAPTER ONE
1.1 INTRODUCTION
In industry there are lots of machinery presents. In this there are more in quantity a rotionational Machinery presents. Phase sequence meter is used for detecting the sequence of the supply in three-phase electric circuits. Since the direction of rotation of three phase electric motors can be changed by changing the phase sequence of supply. And also the correct operation of measuring instruments like 3 phase energy meter and automatic control of devices also depend on the phase sequence. Different types of phase sequence testers are available in today’s market like contact or non contact, static or rotating, etc., in a wide range of voltage or power ratings. The main aim is To check incoming 3 phase supply sequence by Rotating Project kit LED in Clockwise Directions. If 3 phase supply is present in RYB state the start the further circuits. Otherwise If 3 phase supply is not present in RYB (eg.RBY) state the trip/stop of the supply and show as a Line fault Indication with Rotating Project kit LED in Anticlockwise Directions.
1.2 AIM OF THE PROJECT
The main aim is design a device that will check incoming 3 phase supply sequence by Rotating Project kit LED in Clockwise Directions which is carried out by relays. If 3 phase supply is present in RYB state the start the further circuits.
1.3 PURPOSE OF THE PROJECT
In three-phase equipment such as motors and measuring instruments, the correct phase sequence determines whether the motor will rotate in the right direction, or if the instrument works as expected. However, the phase sequence may not be obvious and it is important to have a means of verifying that the sequence is correct, otherwise the system may not function properly or as expected. The purpose of the work is to design a device that perform this work. The two commonly used methods are the phase sequence meter or the static indicator. In this work we are considering phase sequence meter (checker).
1.4 EFFECTS OF WRONG PHASE SEQUENCE
- Reverse Rotation of Motors
- Reverse Pumping.
- Change in Efficiency of Motors.
- Dry Running of large power motors.
- Large running maintenance.
- Overheating of Motors and Burning of Motors Winding
1.5 SIGNIFICANCE OF THE PROJECT
Phase sequence is required for the proper operation of any three phase system. It ensures that the load works as desired, when incorrect, the equipment such as the motor may malfunction, rotate in the reverse direction. The phase reversal may damage the motor or the equipment the motor is driving.
The phase-sequence indicators are used in confirming the wiring in switchboards with a three phase supply.
1.6 SCOPE OF THE PROJECT
A 3-ph supply of 220V AC 50Hz is fed to a logic circuit comprising of NAND gates and OR gates to detect the sequence of R, Y, B by triggering a monostable timer 555.While the sequence is not there the triggering to the timer is missed which is indicated by an LED driven from the output of the 555 timer. If phase sequence reverses Tripping signal generates from NAND Gate and IC555 Timer .The tripping signal fed the i.c, integrated circuit (i.c) or any relay circuit for removing circuit against reverse phase sequence.
1.7 ADVANTAGES OF THE PROJECT
The phase-sequence checker is:
The most straightforward and commonly used tool for determining the phase sequence.
The sequence checker may is digital using semiconductor devices.
The sequence checker is simple and easy to use, but is more costly
1.8 PROJECT WORK ORGANIZATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this works is on the introduction to this work. In this chapter, the background, significance, objective limitation and problem of phase sequence checker were discussed.
Chapter two is on literature review of a phase sequence checker. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
The Title Page should be the first section of your project “Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design And Construction Of A Three Phase Sequence Checker For Three Phase Supply project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work