Construction Of A Gas Leakage Detector Alarm Using Microcontroller
LPG gas is commonly used in our home for cooking purpose. LPG is used in school and college canteens; also it is used in various industries. Accidents never happen with a prior intimation. There are chances of gas leakage due to some negligence or as a result of faulty cylinder. In such cases, if leakage is not detected at an early stage, then it can create huge damages. Arduino microcontroller based LPG gas leakage detector can be used in such situations. This LPG leakage detector is implemented using a ATmega8 microcontroller and MQ-6 gas sensor.
1.0 INTRODUCTION
The use of liquefied petroleum gas (LPG) is increasing quickly, especially in developing countries like Nigeria, Bangladesh,India,South Africa and Nepal, this is because it produces lesser smoke and soot compared to other local available options. The LPG is a flammable mixture of hydrocarbon gases like propane, and butane. LPGs are safely transport throughgas pipelines but this pipelines are prone to wear and tear or break completely which would allow gas leakage, it may also be due to mishandling, accidents or over filling of the gas cylinder. Several times explosionshas resulted from gas pipeline leakages or domestic cooking gas leakage which can be fatal causing loss of property, injuries and or even deaths.Global Economy.com reports that the average daily consumption of LPG has risen to about a thousand barrels per day. This increase in LPG consumption has brought on with it increased rate of accidents often leading to death due to gas leakage and often explosion of gas cylinders. This therefore presents the need for a device that can detect LPG, if present up to a certain level of concentrations in parts of the atmosphere in any environment.
1.1 STATEMENT OF THE PROBLEM
LPGs are useful in our day to day lives, but we open ourselves to possible hazards caused by gas leakages. Whenever excess cooking gas is in the atmosphere any little combustion would lead to a large fire explosion and many have suffered from this accidental occurrence.
Gas detection devices will detect these gases in the atmosphere and precautions can therefore be taken before any unwanted occurrence.
1.2 AIM AND OBJECTIVES OF THE PROJECT
1.2.1 Aim: To design and implement a gas detection system.
1.2.2 Objectives
i. To make a design of the proposed machine.
ii. To carry out the fabrication of machine.
iii. To carry out performance and cost evaluation of the fabricated device.
1.3 SCOPE OF THE STUDY
The scope of this project is to design, fabricate and implementa gas detection device.
1.4 SIGNIFICANCE OF THE STUDY
Gas detectors are an essential application for home and commercial safety; they are also employed in numerous industrial industries. They are used in welding shops to detect combustibles and toxics and in nuclear plants, to detect combustibles. They are also commonly used to detect hazardous vapours in wastewater treatment plants and are very efficient in confined spaces where there is no continuous employee occupancy. Such spaces include tanks, pits, vessels and storage bins. They may also be placed at a site to detect toxins prior to occupant entry where it commonly used for gas leak detection system, fire/safety detection system and gas leak alarm. It can be found in a variety of locations such as on oil rigs to monitor manufacture processes and emerging technologies such as photovoltaic. They may also be used in fire fighting. Typical installation areas being gas yards (Bullets), gas banks with multi cylinders in manifold, user production departments/utility areas like kitchens. Other areas of application and the common gases it can detect are listed in the table below:
1.5 JUSTIFICATION OF THE STUDY
If this project is well carried out successfully, it will help in minimizing bad issues that arises from gas leakages or explosion, as quick fire prevention aids can be carried out immediately gases are detected
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
1.2 PROBLEM STATEMENT
1.3 AIM/ OBJECTIVE OF THE PROJECT
1.4 SCOPE OF THE PROJECT
1.5 SIGNIFICANCE OF THE PROJECT
1.6 JUSTIFICATION OF THE STUDY
CHAPTER TWO
LITERATURE REVIEW
2.0 INTRODUCTION
2.1 A BRIEF HISTORY OF GAS DETECTION SYSTEM
2.2 TYPES OF GAS DETECTORS
2.3 LIQUIFIED PETROLEUM GASES (LPGs)
2.4 PREVIOUS STUDIES RELATED TO GAS DETECTION SYSTEM
2.5 COMPONENT REVIEW
CHAPTER THREE
3.0 METHODOLOGY
3.1 SYSTEM BLOCK DIAGRAM
3.2 MODE OF OPERATION
3.3 DESIGN PROCEDURES
3.4 IMPORTANT TOOLS AND COMPONENTS USED
CHAPTER FOUR
4.0 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE
4.2 PACKAGING
4.3 ASSEMBLING OF SECTIONS
4.5 TESTING OF SYSTEM OPERATION
4.3 INSTALLATION OF THE COMPLETED DESIGN
4.4 TESTING
4.5 RESULT ANALYSIS
4.6 BILL OF ENGINEERING MEASUREMENTS AND EVALUATION
CHAPTER FIVE
5.0 SUMMARY, CONCLUSION AND RECOMMENDATION
5.1 SUMMARY
5.2 CONCLUSION
5.3 RECOMMENDATION
REFERENCES
The Title Page should be the first section of your project “Construction Of A Gas Leakage Detector Alarm Using Microcontroller”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Construction Of A Gas Leakage Detector Alarm Using Microcontroller by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Construction Of A Gas Leakage Detector Alarm Using Microcontroller should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Construction Of A Gas Leakage Detector Alarm Using Microcontroller research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Construction Of A Gas Leakage Detector Alarm Using Microcontroller project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work