Bleaching Of Palm Oil Using Activated Charcoal
This project work is on the bleaching of palm oil using activated charcoal.
The charcoal used for this work was made from pieces of animal bone by carbonization method. It was then activated into two different samples. Firstly, the basic sample was activated using anaphoric acid (H2 s04) while the other was activated by just heating as a control for the experiment; both at a constant temperature of 5000c and approximate time of 2hours.
They were both size reduced into fines and sieved into particle 3ye of 150um portion of the crude palm oil was degummed and neutralized for bleaching. Each interval of bleaching with both the acid activated and the ordinary activated charcoal was 8mins and temperature of 1500c over a hot plate, and subsequent filtration of the solution.
A spectrophotometer was used to measure the absorbance of the oils (crude and bleached) at selected wave length of 480Um. This was converted as the degree of colour reduction expressed in percentages.
Results obtained showed that optimum quantity of the charcoal for bleaching is 5% by weight, of the oil, which gives a percentage colour reduction as 97. 14% for the acid activated and 93.57% for the calcinated sample.
Also, the characterization of both the original oil and the bleaching oil showed that the later has appreciable properties. Hence colour reduction was observable by naked eyes.
INTRODUCTION
1.1 PREAMBLE
Palm oil is one of the various types of vegetable oils, belonging to the group called liquids, because of its fatty acids content.
The majority of the fats contains some colouring matter either as a natural constituent or discoloration produced during the processing. Natural pigments present in vegetable oils are mainly the carotenoid, giving yellow and red colours, and the chlorophylls which give green colours. Colour deterioration can also take place during the extraction process, especially in the local method of extraction used in the most parts of the Eastern region in Nigeria.
Removal or reduction of colours and other components, otherwise called ‘Bleaching” is necessary not only because a pale-coloured fat has an appeal of ‘purity’ but also because the colours of the fat can influence the appearance of prepared food and even more importantly, the pigment present may affect the flavour and stability of the fats and food made from it.
The decolouration (bleaching) could be achieved by chemical treatment, heat treatment and adsorption methods. The most effective and widely used being the later. Thus, in this research project, bleaching by adsorption is carred out using an “Activated charcoal” (an adsorbent), a kind of active carbon, to substitute the use of local clays and the imported ‘Fuller’s Earth – in Palm Oil bleaching, which are rather expensive.
The charcoal can be produced from different sources as from, coal, wood, bone, coconut shell, etc. It would be verified the most suitable form and type of charcoal for effective bleaching and the most favourable condition at which the “activated charcoal could be used, which in them affects the bleach ability’ of the Palm oil itself.
1.2 OBJECTIVE
The objective / aim of this research project is to verify the effectiveness of ‘Activated charcoal’ in the bleaching of palm oil. It will also expose the improvement in the use of local raw material (charcoal) in a chemical process (bleaching), in lien of the imported fuller’s Earth or other adsorbents which more expensive.
1.3 SCORE OF THE STUDY
Basically, this, study dwells on the colours reduction of Palm oil, using an Activated charcoal as an adsorbent (bleaching agent). The major raw materials, Palm oil and charcoal were locally sourced, and information as regards the process were obtained form the literary and other resourceful materials (texts) that treats ‘Adsorption’ as a chemical process.
Title Page
Approval Page
Letter of Transmittal
Dedication
Acknowledgement
Abstract
Chapter one
1.0 Introduction
1.1 Preamble
1.2 Objective
1.3 Scope of study
CHAPTER TWO
2.0 Literature Review
2.1.0 Chemical composition of palm oil
2.1.1 Carotenes
2.1.2 Phosphatides
2.1.3 Gums
2.1.4 Compositions and standards of palm oil
2.2.0 Spoilage factors of palm oil
2.2.1 Preventive measures
2.2.2 Inhibitors
2.3.0 Refining of creebe palm oil
2.3.1 Degumming
2.3.2 Neutralization
2.3.3 Bleaching
2.3.4 Deodorization
2.3.5 Chemical bleaching method
2.3.6 Accretion bleaching
2.3.7 Bleaching by adsorption
2.4.0 Adsorption
2.4.1 Uses of adsorption
2.5.2 Physical adsorption
2.5.2 Chemisorptions
2.6.0 Adsorbents
2.6.1 Bauxite
2.6.2 Decolourising carbons
2.6.3 Gas-adsorbent carbon
2.6.4 Molecular screening activated carbon
2.6.5 Synthetic polymeric adsorbents
2.6.6 Silica Gel
2.6.7 Alumna
2.6.8 Bone char.
2.7.0 Charcoal
2.7.1 Properties of charcoal
2.7.2 Activated charcoal
2.7.3 Methods of charcoal activation
2.7.4 Properties of activated charcoal
2.7.5 Chemical properties of activated charcoal
2.7.6 Physical properties of activated charcoal
2.7.7 Uses of activated charcoal
CHAPTER THREE
3.0 Experimental method
3.1.0 Materials
3.1.1 Material treatment
3.2.0 Charcoal activation using acid
3.2.1 Charcoal activation by heat treatment
3.3.0 Degumming of Palm oil
3.3.1 Neutralization
3.4.0 Bleaching of palm oil
3.4.1 Experimental set-up
3.5.0 Characterization of palm oil
3.5.1 Specific gravity
3.5.2 Iodine value
3.5.3 Free fatty acid
3.5.4 Saponification value
3.5.5 Esterification value
3.5.6 Process flow chart
CHAPTER FOUR
4.0 Experimental result
4.1.0 Effect of bleaching sample
4.2.0 Effect of temperature on bleaching
4.3.0 Colour observation at absorbance
4.4.0 Concise table for characterization
CHAPTER FIVE
5.0 Discussion
CHAPTER SIX
6.0 Conclusion
CHAPTER SEVEN
7.0 Recommendation
References
Table of nomenclature
Appendices
The Title Page should be the first section of your project “Bleaching Of Palm Oil Using Activated Charcoal”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Bleaching Of Palm Oil Using Activated Charcoal by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Bleaching Of Palm Oil Using Activated Charcoal should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Bleaching Of Palm Oil Using Activated Charcoal research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Bleaching Of Palm Oil Using Activated Charcoal project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work