Design And Installation Of 200 Watt Solar Power System
The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective gadgets like cut out switches; to give the 200W expected. The solar panel was mounted outside the building to allow for maximum collection of sun energy. It is expected that the system will help the department meet up with its office duties even when central power is not available.
INTRODUCTION
1.1 NEED FOR THE PROJECT
The general objective of the system is to provide efficiency, steadiness in the use of power appliances, by ensuring continuous availability of power supply even in the absence of mains. Uninterruptability of the system made it possible to eliminate all suspense from mains outage during the execution of an important and urgent assignment as may be required.
For better production of the system, the system was operated at a fully charged condition of the battery.
The project was rated 200W of 220V and 50Hz. It was expected that at this condition, it was favourable to carry load of the stipulated power. Loads of low power factors are not helpful since they produce spikes. Overloading is not potent to provide zero change over time and the inverter had LEDs which indicates mains failure and battery discharge and system fault.
1.2 SCOPE OF STUDY
This solar power source makes it possible to provide a clean reliable supply of alternative electricity free of sags or surges which could be found in the line voltage frequency.
The solar power system (SPS) system achieved this by direct current from solar panel and by rectifying the standard main supply, using the direct current to charge the batteries and to provide clean alternative power by passing the energy a filter system.
It has zero change over time and LEDs which indicates mains fail and battery discharge level and it provides 100% protection against line noise, spikes surges and audio frequency interference.
1.3 DEFINITION OF TERMS
1. Inverter unit: This unit converts a DC voltage into AC voltage with the help of the inverter unit.
2. Automatic Control Unit: This provides all the required control needed to meet up the objective of the whole system
3. Battery Unit: This is a secondary cell unit, capable of storing enough DC voltage from either sun or AC main, of which is later converted to AC voltage.
Title Page
Approval page
Dedication
Acknowledgement
Abstract
Table of content
List of figures
List of tables
CHAPTER ONE:
1.0 INTRODUCTION
1.1 Need for the project
1.3 Scope of study
1.4 Definition of terms
CHAPTER TWO:
2.0 LITERATURE REVIEW
2.1 The basics of solar power system
2.2 Principle of solar panel
2.2.1 Estimating system out
2.2.2 Standard test conditions
2.2.3 Temperature
2.2.4 Dirt and dust
2.2.5 Mismatch and wiring losses
2.3 Solar charge controller
2.4 Principle of inverter
2.4.1 Inverter sizing
2.4.2 DC to AC conversion losses
2.5 solar battery
2.5.1 Temperature effect
2.5.2 Battery voltage
2.5.3 Battery power conversion efficiency
2.5.4 Monitoring and maintenance
CHAPTER THREE:
3.0 SYSTEM OPERATION
3.1 Block diagram of the system
3.2 System operation with block diagram
CHAPTER FOUR:
4.0 SYSTEM DESIGN
4.1 Load evaluation and power consumption table
4.1.1 Calculating power consumption
4.2 Battery sizing
4.3 Solar panel sizing
4.3.1 Typical Pv electrical system types
4.3.2 Solar array sizing worksheet
CHAPTER FIVE:
5.0 PROCUREMENT AND INSTALLATION
5.1 Procurement
5.2 Determination of installation site
5.2.1 Mounting options
5.3 Installation procedure
CHAPTER SIX:
6.0 TEST AND RESULT
6.1 Test and results
CHAPTER SEVEN:
7.0 CONCLUSION AND RECOMMENDATION
7.1 Conclusion
7.2 Recommendation
7.3 Limitation
Reference
The Title Page should be the first section of your project “Design And Installation Of 200 Watt Solar Power System”, providing essential details like the project title, your name, your supervisor’s name, the institution, and the submission date. After that, the Abstract offers a brief summary of your project, touching on its purpose, methods, results, and conclusions in 150-300 words. The Acknowledgments section is where you can thank those who supported your research, such as your supervisor, peers, or organizations that provided resources.
Next, the Table of Contents organizes the Design And Installation Of 200 Watt Solar Power System by listing its chapters and sections, along with page numbers for easy reference. The List of Figures and List of Tables help guide readers to specific visual elements like graphs, charts, or tables included in the document. There should also be an Abbreviations and Glossary section to explain any specialized terms or acronyms, making the content clearer to readers unfamiliar with the technical language.
The main body of the Design And Installation Of 200 Watt Solar Power System should start with the Introduction, which provides background information, outlines the research problem, states your objectives, and gives a brief overview of your research methods. Following that, the Literature Review offers an in-depth look at previous research relevant to your project, identifying gaps your study aims to address. The Methodology section then explains the research design, tools, and data collection methods you used to conduct the project and analyze the data.
In the Results and Discussion section, you present your findings and discuss them in relation to the Design And Installation Of 200 Watt Solar Power System research questions or objectives, often using tables or charts to help explain the data. The Conclusion summarizes the key results, discusses their implications, and suggests possible directions for future research. You may also include recommendations based on your findings, offering practical advice for improvements or applications. Finally, the Design And Installation Of 200 Watt Solar Power System project should include a References or Bibliography section to list all the sources you cited, as well as Appendices for any additional material. A Statement of Originality is often included to confirm the authenticity of your work